• Finding I&I faster

    WEF Webinar

How flow monitoring turned miles of I&I investigation into a couple hundred feet

In this on-demand WEF webinar, experts from Emerald Coast Utilities Authority (ECUA), Flow-Tronic and Badger Meter explore how targeted flow and level monitoring can help utilities identify where excess water is entering their systems and focus investigative resources.

See how ECUA used flow, rainfall and lift-station data to isolate problem areas, prioritize field investigations and make more informed decisions about where to act.

Watch Webinar Contact us

Why finding I&I requires better data

Inflow and infiltration consume valuable collection-system capacity, increasing the risk of surcharging and sanitary sewer overflows during heavy rainfall. But knowing that excess water is entering the system doesn’t tell utilities where it’s coming from.

Targeted monitoring helps utilities move from systemwide problems to focused investigations.

Vincent Favre, North American Manager at Flow-Tronic; George Elaro, Sales Engineer at Badger Meter; and Mark Robertson, Manager of Wastewater Infrastructure at ECUA, share practical approaches to identifying and investigating I&I.

Together, they discuss how dry- and wet-weather flow comparisons, rainfall correlation and site-specific monitoring approaches help utilities identify areas that warrant closer investigation.

Case Study

ECUA results at a glance

ECUA manages nearly 900 miles of gravity main across Florida’s Escambia County. Heavy rainfall, high groundwater and aging infrastructure make I&I a persistent challenge, while traditional monitoring practices limited the utility’s ability to pinpoint problem areas efficiently.

By bringing monitoring in-house and deploying equipment where it was needed, ECUA achieved a more focused approach to I&I investigation:

  • Narrowed an investigation from several miles of pipe to a couple hundred feet
  • Identified six to eight lateral breaks allowing stormwater into the sanitary system
  • Helped field crews avoid unnecessary testing across a larger basin
  • Gained greater flexibility to reposition monitors as investigative priorities changed
  • Used rainfall and flow data to identify areas requiring closer investigation

This approach gives ECUA a more flexible foundation for ongoing I&I investigation, rehabilitation planning and performance monitoring.

FAQs from the ECUA project

How do utilities determine where to begin an I&I investigation?

Comparing dry- and wet-weather flow helps identify areas showing unusual rainfall response. At ECUA, lift-station alarms, runtime reports and rainfall data help staff identify areas that warrant closer investigation and determine where to deploy monitoring equipment.

How do utilities determine which flow monitoring technology is right for a location?

Equipment selection depends on flow depth, velocity, pipe characteristics, site access and maintenance requirements. ECUA uses Raven-Eye 2 non-contact meters in smaller, low-flow basins and Beluga submerged area-velocity meters in larger trunk mains.

How long should utilities monitor an area before taking action?

Monitoring duration depends on the investigation’s objectives and the conditions being measured. Following a four-inch rainfall event, ECUA collected approximately one month of data to identify which mains were contributing to the wet-weather response.

How does flow monitoring improve traditional investigation methods like smoke testing and CCTV?

Flow monitoring helps identify where excess water is concentrated, allowing utilities to narrow the area requiring investigation. Crews can then use smoke testing, CCTV or other inspection methods to locate the actual source rather than investigating an entire basin.

How can utilities measure whether I&I rehabilitation efforts are working?

Monitoring before and after rehabilitation allows utilities to compare changes in system response. ECUA is collecting rainfall inflow data in a neighborhood identified for sewer rehabilitation, with plans to compare pre- and post-rehabilitation results to evaluate the project’s effectiveness.

Key Takeaways

Dry- and wet-weather comparisons help identify where excess flow is concentrated.

Rainfall and system data provide context for recognizing abnormal flow response.

Site conditions determine the appropriate monitoring technology and approach.

Targeted monitoring helps focus smoke testing, CCTV and other field investigations.

Pre- and post-rehabilitation monitoring helps utilities evaluate changes in system performance.

See for yourself

Find the right monitoring approach for your collection system

From small, low-flow basins to larger trunk mains, Flow-Tronic’s Raven-Eye 2 and Beluga flow meters support different monitoring needs across wastewater collection systems.

Explore our monitoring technologies or connect with our team to discuss your collection-system challenges.

Explore our products Contact us